I know this is a year old, but I have to ask; any chance the impedance mis-match would
hurt the little OT in these guys? I know usually up is ok but down is bad.
Hello!
The DSL 40CR is the tits. The circut is different than the DSL 40C. I've run it with a well broken in V30 and a Weber G12H clone. Preamp tube rolling, especially in the V1 hole, can be rewarding. I found the factory V type speaker too bright. I didn't take the time to break it in. I...
I bought a quad of cryo'd =C='s cheap years ago and they are the balls. Bias is key. I run them in a JCM 2K DSL50 and DSL40CR and I can get everything from that throaty giant kazoo with a midrange knob to Dual Showman with the right P tubes and bias in both amps. They sing.
I bought a vin 10 for a PRRI, and it does do a good job of getting a V30 sound. Prob a little more hi-mids than a GB10 but you can eq that to some degree. I wound up putting the factory "jensen" 10 back in after modding the tone stack and neg feedback on the PRRI, and it sounds good with the...
I spent a lot of time rolling tubes, biasing and speaker change-outs trying to get a "C" to sound like a first release
DSL50 I was running through a 1960A cab loaded with old V30's and Greenbacks. I had given up, but heard about the newer "CR" model that had a reworked circuit, and consensus on...
As others have already mentioned tubes, both pre, power and bias, the last remaining contributors to your signal chain are pickups and speakers. High output pickups will help drive your preamp section into distortion. Speaker sensitivity around 100+ will make your amp sound louder.
look for...
Hello; I would get several 12ax7's, like a Tungsol or Mullard reissues, or even a JJ or 2, and replace V1 with each, and turn your knobs until you find one that gives you a nice clean, yet growls on overdrive. An aggressively voiced V1 might be ok if you don't want nice cleans. Your amp tone...
Absolutely. I rarely go above 8 on my bridge pups, but neck sometimes 10. It depends on the
tune. I play mostly covers and try to achieve a reasonable facsimile of the tone therein. I run my DSL'S with the treble and presence on 1, and have my top end and chime come from the
way I have my power...
I have seen that before...soft bias 6550's = a little more Fendery cleans and early compression.
I'm sure he ran everything as loud as possible before run away, and tweaked his vol as a compressor
to effect. He used his fuzz-face the same way. You can hear him doing both on his recordings, live...
I ordered an Alder strat body from Warmoth With a "left handed" bridge pickup rout, major difference. He also used very light wound strings so they would not boom with the bass turned up to get as fat a tone as possible on the high strings, and were more evenly balanced with the hi in output.
I have spent many hours rolling tubes in the afore mentioned amps. It's really quite amazing how you can tweak the tonal characteristics of both the preamp and output sections and their contribution to the overall sound. Back in the day, spec's were adhered to as best as could be.
Things were...
I spent some time rolling tubes in the loop, and it matters what's in there as far as both the tone and volume, ymmv of course.
Also the pedals and order going in. I haven't tried any "rack"
level output gear in it though. It also seemed to me that it affected the overall tone somewhat, on or...
That would be most illuminating. I just got through rolling tubes and the final recipe with the Weber C123055 that I bought for the "other" 40C, is quite close to what I run in my 2kDSL50 head. The
bright cap tweak would be the cherry. Y'all still have snow on the
ground up there?
Yes, compare them at least. Maybe Micky knows. I liked around 200pf for c19, and I think 68pf for c4. So we're stuck with speaker and tube changes/bias 'till someone in the know pipes in. But it sounded good out of the box, surprisingly. Bounce, bloom....just
a little too much high end.
Has anyone ID'd the channel bright caps on the new DSL40cr, or seen a schematic?
I had a 40C, and went through an exhaustive exercise trying to get it to sound close to a 2kDSL50
head I have which kills. Couldn't get there. I saw the new DSL's were different than the originals,
so I went to my...
AMS! I've got my 401 chassis out of the box for some final tweaks and was wondering if you'd share the 2 cap numbers that you swapped for the 50uf's. My soldering is not the neatest and
I dread trashing this board every time I plug in the iron. Thx.
Not really surprised, disappointed would be more like it.
I recently went through a rectifier tube sag, power tube bias exercise with a Deluxe Reveb Re-issue. Yet another door opens.
Yea, I looked at the schematic after your previous post, and saw
all those caps you mentioned going straight to...